Rigging Your New Kayak For Fishing

So you bought a new kayak, and now you need to rig it. Where should you begin?

The first thing I tell people is always wait to drill into your new kayak and add accessories until you have been on the water a few times. Why do I say this to them? Simple– if you go and put a bunch of accessories on your kayak before you had it on the water, now they are in that spot with holes drilled forever. Unless you or someone you know can plastic weld. This also gives you a few times on the water to figure out where and what gear will work best with your new kayak.

Yes, there are some basic things you can add right when you bring your new boat home, not all things have to wait. For instance, you can figure out a place to put a fish finder, if you use one. On the Wilderness Systems A.T.A.K. 140, it is most commonly mounted on the Flex Pod OS Removable Console. It was designed to be able to mount a RAM MOUNT and hold your battery inside by adding the Wilderness Systems Flex Pod OS Electronics Kit. This gives you all the needed hardware to mount a transducer to the bottom of the POD. It also provides a pre-formed piece of compressed foam to hold the battery in place inside it.

When I received my new A.T.A.K. 140, I had already pre-planned a few of my rigging setups based on experience with other kayaks and from ideas that others have shared. Using social media, you can find groups online that are dedicated to specific brands and models of kayaks. This may help you see some of the rigging options and possibilities that others have already experimented with for the kayak you have chosen.

These questions are all very important to ask yourself. The list could go on and on, but those four questions should help you decide what is most important for you on the water. You can always add additional equipment after more time on the water. Sometimes adding a few items at a time is best. This way, you make sure you're getting everything in its proper place and not crowding your reach and deck space on the kayak.

One of the first and most important items to be added should always be a paddle leash. This helps keep your paddle secured to your kayak, and in some areas is required. It is an inexpensive item and very worth it. Although most modern paddles float when in the water, you should always have it leashed to your kayak.

Some of the hardest decisions to make can come when it is time to decide where to add Mighty Mounts to your kayak or extra Gear Tracks. These give you the ability to mount cameras, rod holders, and many other accessories in specific places. When mounting these products you also have to decide if you will need the backing plates for them or not. When deciding on this, think of what you will be mounting where. If you will be mounting a rod holder there and trolling with it, then you will need to add the backing plate. However, if it will just be holding a small action camera or something light-duty, then you will be fine without adding the backing plates.

Many kayak anglers have found it useful to install flush mount rod holders on their kayaks. These can provide many different uses with today’s accessories on the market, from holding fishing rods to high-rise rod holders. If you decide to install them make sure to layout where you want them, and measure twice by rule. As you will be making a significant hole in your kayak to install them.

With my current A.T.A.K. 140, I took my wiring to a different level this time. I added a battery voltmeter to the FlexPod OS so that I could monitor the charge on the battery powering my fish finder. I found this very useful as I also use it as a GPS for open-water fishing. Next to the voltmeter, I added a dual USB port so I could charge my cell phone or other devices if needed while on the water. In the rear of the kayak, I also added another battery to power two Waterproof USB ports which power the action cameras on my kayak. This provides a direct power source to them for all-day filming on the water without having to change the batteries.

When you are finally ready to rig your new kayak or maybe even just add some accessories to your existing one, there is one thing that can be rather intimidating for many kayak anglers. Drilling that first hole in their kayak. Yes, this can and more than likely will be rather intimidating, but rest assured that there are plenty of products on the market to help you make it watertight at those points. Whether it be the use of a well nut, rubber gasket, or marine-grade silicone.

Remember before rigging to take your time and choose wisely. There is no rush, and make sure that you add the accessories that will truly benefit your needs on the water.